Home | Courses | CERTIFICATE III IN LIGHT VEHICLE MECHANICAL TECHNOLOGY

CERTIFICATE III IN LIGHT VEHICLE MECHANICAL TECHNOLOGY

National ID: AUR30616 | State ID: BAE6

 

Fine tune your automotive career.

When you are employed as an apprentice automotive mechanic you be required to complete this course, which will see you quailified as a Light Vehicle Automotive Service and Repair Technician.

Automotive students at the Midland campus enjoy quality facilities including modern vehicles, specialised diagnostic equipment, and fully equipped classrooms and workshops.

You will learn to service light vehicles; diagnose and repair many vehicle systems including braking, transmissions, steering, suspension, cooling, charging and starting systems; and workplace safety and health.

The Certificate III in Light Vehicle Mechanical Technology is an apprenticeship: you must be employed in a training contract by an appropriate organisation to study. Please see the Apprenticeships section for more information.

Entrance Requirements

Prerequisites

Study pathway

Job opportunities

Important information

Entrance Requirements
Prerequisites
Study pathway
Job opportunities
Important information

Delivery location, important dates and study options

Overview

Fees and charges

Units

How to apply

Overview

Course Overview

Where Midland
Duration

Three years (6 semesters) part time

HowApprenticeship
WhenWas available Semester 2, 2017
Available Semester 1, 2018
Fees and charges

Local full time students

Course fees are made up of two components, tuition fees and resource fees.

Tuition fees are determined by multiplying the course fee rate by the nominal hours, which is the number of hours in which an average student could be expected to complete each unit. They are not the hours of training or instruction.

Resource fees are charges for material that are essential to a course or unit, and are purchased by NMT to be used by students during the course.

Fees may vary depending on the units you are enrolled in so an approximate amount has been shown. You will be given the exact amount of your fees at enrolment. Part time student fees will vary depending on the number of units you are enrolled in.

Please note, you may also need to buy textbooks or equipment for your course.

For details see the indicative fees list here.

International Students

If this course is available for International students you will need to pay your course fees to TIWA when you accept your offer.

Units

Apprenticeship courses can only be studied when you are employed as an apprentice.

Electives may change depending on the skills required by the employer.

Stage 1A
Unit Title National ID Unit of Study
Carry out servicing operationsAURTTA004AXB11
Follow environmental and sustainability best practice in an automotive workplaceAURAEA002AXE88
Follow safe working practices in an automotive workplaceAURASA002AXE64
Inspect and service enginesAURTTE004AXA74
Test, charge and replace batteries and jump-start vehiclesAURETR025AXD79
Use and maintain measuring equipment in an automotive workplaceAURTTK001AXA63
Use and maintain tools and equipment in an automotive workplaceAURTTK002AXA64
Stage 1B
Unit Title National ID Unit of Study
Carry out vehicle safety inspectionsAURTTA017AXA99
Diagnose and repair light vehicle hydraulic braking systemsAURLTB003AXC59
Diagnose and repair light vehicle steering systemsAURLTD004AXC53
Diagnose and repair light vehicle suspension systemsAURLTD005AXC52
Inspect and service braking systemsAURTTB001AXA89
Inspect and service steering systemsAURTTD002AXA79
Inspect and service suspension systemsAURTTD004AXA78
Stage 2A
Unit Title National ID Unit of Study
Diagnose and repair automotive electrical systemsAURETR032AXD72
Diagnose and repair electronically controlled steering systemsAURETD001AXE18
Read and apply vehicle wiring schematics and drawingsAURETR016AXD87
Solder electrical wiring and circuitsAURETR006AXD97
Test and repair basic electrical circuitsAURETR012AXD93
Stage 2B
Unit Title National ID Unit of Study
Diagnose and repair charging systemsAURETR029AXD73
Diagnose and repair cooling systemsAURTTC003AXA82
Diagnose and repair ignition systemsAURETR031AXD74
Diagnose and repair light vehicle enginesAURLTE002AXC46
Diagnose and repair starting systemsAURETR030AXD75
Stage 3A
Unit Title National ID Unit of Study
Diagnose and repair light vehicle clutch systemsAURLTX003AXC33
Diagnose and repair light vehicle drive shaftsAURLTQ002AXC36
Diagnose and repair light vehicle final drive assembliesAURLTQ001AXC37
Diagnose and repair light vehicle manual transmissionsAURLTX001AXC34
Inspect and service automatic transmissionsAURTTX003AXA23
Inspect and service manual transmissionsAURTTX002AXA24
Stage 3B
Unit Title National ID Unit of Study
Carry out diagnostic proceduresAURTTA018AXA98
Diagnose and repair engine forced-induction systemsAURTTF005AXA69
Diagnose and repair light vehicle emission control systemsAURLTZ001AXC30
Diagnose and repair spark ignition engine management systemsAURETR023AXD81
Inspect and service diesel fuel injection systemsAURTTF002AXA70
Inspect and service petrol fuel systemsAURTTF001AXA72
How to apply

If this course uses TAFE Admissions, to study full-time in 2017 apply through tasonline.tafe.wa.edu.au.

Part time enrolments are usually done in late January and mid June each year while online and continuous enrolment courses normally have enrolments available at any time, for help enrolling or for more information:

call: 1300 300 822 or email: enquiry@nmtafe.wa.edu.au

International students please contact www.tafeinternational.wa.edu.au.

For apprenticeships and traineeships, you must be employed in a training contract by an appropriate organisation to study.

For all other enquiries please call us on 1300 300 822 or email: enquiry@nmtafe.wa.edu.au

Enquire now
Call us
Email us

Please make sure you select a campus in the units tab otherwise no course study plan information will be printed.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

To study full-time in 2018 you can apply now through tasonline.tafe.wa.edu.au.

For information about applying to study in other ways, including part-time, work based and online, please visit our Apply and Enrol page.

International students please contact www.tafeinternational.wa.edu.au.

For apprenticeships and traineeships, you must be employed in a training contract by an appropriate organisation to study.

To study full-time in 2018 you can apply now through tasonline.tafe.wa.edu.au.

For information about applying to study in other ways, including part-time, work based and online, please visit our Apply and Enrol page.

International students please contact www.tafeinternational.wa.edu.au.

For apprenticeships and traineeships, you must be employed in a training contract by an appropriate organisation to study.

Qualification level

1
1

Links

Page last updated December 14, 2017